Pyro Industries Quest Plus Instrucciones de operaciones descargar pdf (Pagina 18)

Stove Vent Pipe/ln ta ke Installa tion

IT IS RECOMMENDED THAT ONLY AN AUTHORIZED DEALER INSTALL

YOUR PELLET STOVE. THE FOLLOWING INSTALLATION GUIDELINES

MUST BE FOLLOWED TO ENSURE CONFORMITY WITH BOTH THE SAFETY

LISTING OF THE STOVE AND LOCAL BUILDING CODES.

General guidelines for installing the exhaust system:

3 or 4 inch listed type

"L"

pellet vent exhaust system must be used for freestanding installations and

attached (and sealed) to the pipe connector provided on the back of the stove. Use a 3-to-4 inch adapter or

a 3-to-4 inch Tee in order to run

inch pipe.

The vent termination must be located no less than

48"

(1.2114 from any opening through which flue gases

could re-enter the building,

(i.e. windows and doors) not less than

24"

(.6m) from an adjacent building,

and not less than

(2.2m) above grade when located near public walkways. The final termination of the

exhaust system must be configured so that flue gases do not jeopardize the safety of people passing by,

overheat combustible portions of nearby structures or enter the building. Keep brush, plants and shrubs at

least 36"

(.9m) away from vent termination. Since sparks may escape from the exhaust pipe of any stove,

always use caution when positioning the vent pipe. (Refer to pipe manufacturer's instructions when

installing and terminating the exhaust.)

Ninety-degree elbows accumulate fly ash and soot which reduces the exhaust flow and performance of the

stove. Horizontal runs of pipe will collect fly ash as well. It

recornmended that a single or double clean-

out 'tee' be installed at every 90 degree turn so that fly ash can accumulate at the bottom of the 'tee'. If a

90 degree turn connects a vertical run of pipe to a horizontal run (as you follow the exhaust away from the

stove), a tee

not required. At any other 90 degree turn, installation of a clean-out tee is recommended to

permit periodic cleaning of both the horizontal and vertical runs of pipe.

Total length of horizontal vent must not exceed

25ft. (7.7m). See page 17

CAUTION:

all direct vent installations (short, horizontal runs); care should be taken when choosing

a location for terminating the vent.

(It

NOT

recommended to directly vent the exhaust on the prevail-

ing wind side of the house).

"DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THlS UNIT".

"DO NOT CONNECT

THlS TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE".

FIREPLACE INSERT:

single-wall, stainless steel flexible or rigid exhaust pipe may

used for insert installations and must

be attached to the stainless steel exhaust tee provided with each insert model stove.

When venting into an existing chimney (masonry or factory built) thechimney must be cleaned, with all

creosote, dust and ashes removed.

The

"L"

vent or single wall stainless exhaust system must be installed so as to

GAS TIGHT! The vent

manufacturer's installation procedures must be followed. In addition, pipe connections, joints and all pipe

seams within the home should be sealed with room temperature vulcanizing, high temperature

silicone sealer

(RTV).

If an insert

to be installed into an unlined masonry chimney, 3" or

rigid or flex pipe must be extended

to the top of the existing chimney. The top of the existing chimney should be sealed with a metal plate after

the pellet vent has been installed.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 39 40

Comentarios a estos manuales

Sin comentarios

Pyro Industries Quest Plus Instrucciones de operaciones Pagina 18

Comentarios a estos manuales

Relacionado con productos y manuales para Estufas Pyro Industries Quest Plus